Видео

when i was a toddler maybe 2-3 i was staying in a small town in Québec thats a ghost town, so there are no traffic lights and everyone knows everyone, because there were so little people and no lights i could see the night sky just like that, i remember waking up at night and looking out the window, i grabbed my blanket and my baby doll and walked outside at maybe 3 am (this was the middle of summer btw) and just laid out on the grass and looked at the stars, my parents found me asleep on the front lawn

Very impressive! Good planning = great outcome. 🙂

Removing the skid plate was some good information. Thanks

Wtf this quality video I was not expecting and audio was clean… SUBBED

How much?

I have a 2020 ford ranger and recently started misfiring I thought it was the spark plugs so I replaced then with new set of ignition coils and it ran fine for a day then it started doing it again,now I'm thinking it's probably a fuel injector issue probably, but either way I'm gonna take it in and get it checked instead

The way the stars go should be the indicator of the shape of our planet, which is flat.

What Year ford explorer

Did your lift void warranty and what kit did u use

Great video thanks. You mentioned you have 33s on your truck. what offset wheels do you have to fit that? I also have a 2 1/2 inch leveling lift

You didn't have to shim the posts at all???

Thank you. I was going to take my truck to the dealer but i don't trust it anymore. I tather do it my self.

Good riddance. Those decals are ugly AF

Thank you. I was thinking it would be way harder.

Thanks, it worked out well.

Either science is wrong or this is fake. If earth is orbiting the sun, and our solar system is moving through the milky way galaxy at 65,000 kph, it is impossible for the stars to remain in an elliptical orbit about earth's rotational axis. Impossible.

To each his own. I like that decal on my F-150.....

GD that music sucks A.

Y

Doesn’t this work without the pixlas mod?

Do u feel the car spend more oil after the liftup ??

I bought a Craftsman wall cabinet. It was advertised as 28" wide. It was actually 26 1/2" wide. Are your cabinets 28" wide? Thank You for your informative video.

mine were installed on a flat wall with the same cleat at the top. as a result they look like they're pulling away from the wall and scare the crap out of me. Can you tell me how deep the pallet wood is at the bottom of your cabinet so I can figure out what to screw in back there at the bottom so they'll stay straight on the wall. Thanks. Ps. Genius idea with the pallet wood on the wall! you don't have to worry about scuffs and you can literally hang anything anywhere now!

Super.. Merci!

5:44 Looks like it would fold flat by unscrewing "something" where he is unhooked it.

That same fluid extractor doesn't work on our ranger. It leaves 3 qts behind and that has nothing to do with the extractor because the extractor works flawlessly. The shape of the pan is the problem. So I don't understand how it worked for you.

Looks like the stars are moving to me.

Worked like a charm! Thx

That's not the jacking point, the jacking point is on the sill, these squares were used when the cars were being sprayed in the factory. I'd honestly suggest beefing up the floor pan also if you wish to use that square to jack the car up.

Your hair dryer is amazing. Do a video on it.

Awesome build!

Thanx M8, very useful. that is a lot of space we have now, just as I want.

Love the content man

I still saw some residual glue

How tall are you? I'm a bit over 6' and looking for a lift that can lift my CCLB F250 while I stand under it. There's the 10,000 lb Extra Tall 2-Post Lift that I may end up getting.

Did you keep the stock lug pattern or did you change the axles? And what year explorer did you pull the rear end from?

Great work. All I can say is I'm thankful my 2008 Ranger Sport was optioned from the factory with the 8.8 with limited slip. It's got no rust on the body has less then 50k miles and has the 4.0. I just got it last year and figured I'd have to get an 8.8 out of an Explorer but this evening I looked under the truck and got the axle code off the door sticker. It was a nice suprise.

Do you have a link or part number to the Rigid cases?

Oil dilution isn't just a Ford issue, it's any engine that's a GDI. If you drive short trips frequently and do not get on the highway very often you'll need to change your oil frequently.

Why did you remove the fan? Why not just disconnect the fan shroud from the old radiator?

Settings pls

Good video, Harles. Can we invite you to do a review for our product? We have emailed you to inquire about an opportunity

All heavenly bodies supposedly millions of miles apart moving at the same speed should make anyone question.

As a matter of interest; are you getting any money or commission from FORD for advertising their products, or are you doing it for free?

Did you consider drilling holes the diameter of the round spacers in the gutter trim rather than cutting the gutter trim into segments? It looks like you could fit the spacers into holes drilled into the gutter trim...

Thanks for sharing. Do you know where to get the front plate and bar that supports front lights and holding the cooler? Is there new parts available somewhere? I AM located in Sweden, best regards

Thanks!

When I installed mine, I removed the middle screws in the bottom back and moved them outward to the next holes. Then I used a 3x3 block of 3/4" wood and screws and screwed into the wall to secure them better. I didn't use the Versatrack to hand either, I used Rubbermaid Fasttrack. Been 15 years and they are solid still.

♥

flat